1 Sistema de Portero Eléctrico Kantech KTESTYCO '05 GLM 9/24/ :42 PM Sistema de Portero Eléctrico Kantech KTES (Speaker's Name)
2 Agenda Principales características Especificación Número de ParteTYCO '05 GLM 9/24/ :42 PM Agenda Principales características Especificación Número de Parte Conexión del Hardware Utilizando la unidad Programando el KTES – Modo independiente Estado de la unidad Reiniciar la unidad Conexión con EntraPass Conexíón con control de acceso (Integración Wiegand) (Speaker's Name) 1
3 Kantech KTES Sistema de Portero Eléctrico para:Edificios de apartamento Comunicdades cerradas Condominios Edificios de oficina Fábricas Sitios industriales Diseño y apariencia de calidad Robusto y anti-vandalico
4 Principales CaracterísticasModo independiente o integrado con sistema de control de acceso Conveniente programación remota y administración con el software EntraPass Facilmente programable, directamente desde el teclado Directorio electrónico con capacidad para 3,000 inquilinos Soporte a lectores para caracteristicas de control de acceso Seleccion de idioma dinamina para el visitante Anti-vandalico, 4-lineas, 20-caracteres LCD con retroamimentación de alto contraste Caja de acero inoxidable resistente a la intemperie y anti-vandalica Botones de función contextual para una sencilla operación del sistema Número de telefono alternado disponible para llamar al inquilino Capacidad de reportes de alarmas y problemas versatil Cifrado de 128-bit en la placa, comunicación IP segura con EntraPass Opcional, cubierta con cámara de video a color para mayor seguridad Bateria de respaldo supervisada garantiza una operación continua por un mínimo de 4h. Una sola línea telefonica soporta hasta 5 unidades
5 KTES – Por dentro – por fuera
6 Especificaciones FísicasTYCO '05 GLM 9/24/ :42 PM Especificaciones Físicas Dimensiones para colocar en superficie (Alura x Ancho x Profundidad) x x 9.91 cm (11.5 x x 3.90 pulg) Peso 7 kg (15.4 lb) Montaje Superficie, flush, o cuello de ganso Construcción Calibre 14 de acero inoxidable montado en caja de calibre Pintura resistente a la intemperie “Epoxy” negra Bocina con material de fibra a prueba de agua Microfono omni direccional de alta calidad en una cámara acustica Condiciones de Operación Temperatura 0° a 49°C (32° a 120° F) -35° a 49°C (-31° a 120° F)* Con kit de calor opcional Humedad 0 a 95% no condensado Built in thermostat set to activate relay between 5° and 10° (Speaker's Name)
7 ¿Superficie o Flush?
8 Superficie o Flush
9 Especificación OperacionalTYCO '05 GLM 9/24/ :42 PM Especificación Operacional Capacidad: Hastap 3,000 inquilinos; 4,000 eventos en modo autonomo; 1- a 5-digitos para ID del inquilino; 4- a 6-digitos para PIN del inquilino; 2 números telefónicos por inquilino (hasta 24 digitos) 1 Lector Pantalla: A prueba de vandalismo 4-líneas x 20-caractereres LCD Alto contraste y luz de fondo Mensajes de bienvenida personalizables 2 Mensajes por idioma (hasta 4) Tiempo de despliegue variable (0-255 segs) Programación: Directamente desde el teclado Remotamente con el software EntraPass Effect of delay 0, will keep on screen (Speaker's Name)
10 Especificación OperacionalTYCO '05 GLM 9/24/ :42 PM Especificación Operacional Tiempo de llamada: 10 segundos a 1 hora con advertencia de tiempo restante Línea Telefónica: Tono de pulso o rotativo (hasta 5 unidades en la misma línea) TIP y Ring son reversibles (Valor REN es 0.1) Puerto Wiegand: Interfaz de Control de Acceso Wiegand Led de Lector para validar el estado de la salida de la cerradura Entradas Supervisadas: 4; sencilla, doble y/o sin FDL Cableado máximo: 600 m (2,000 pies) utilizando #22 AWG Puertos de Comunicación: Ethernet 10/100Base-T con RJ-45 (Hasta 100Mbps) RS-485 (Hasta 115,200 baud, detección automatica) Línea telefónica (hasta 2,400 baudios por modem) Tenant are required to have a touch-tone line. Buzzer and LED are not working. LED goes green whenever door is unlock but that’s it. (Speaker's Name)
11 Especificación EléctricaTYCO '05 GLM 9/24/ :42 PM Especificación Eléctrica Energía de Entrada Norte América 16 VAC, 40 VA Internacional 19 VDC (100 VAC ~ 240 VAC, 50~60 Hz), 3.15 A Salida Auxiliar DC 12 VDC, 450 mA Salida de Cerradura 12 VDC, 650 mA 3 Relé en la placa Forma C 30 VDC / 24 VAC ; 3 Amps c/u Salida del Lector 5 VDC or 12 VDC (175 mA) o energía supervisada externa (max 1A) Configurada con JP9 When using external power supply, power must be at least 5V. (Speaker's Name)
12 Número de Parte - AccesoriosTYCO '05 GLM 9/24/ :42 PM Número de Parte - Accesorios KTES-FBOX Caja KTES flush para instalación flush con anillo de compensación, negro KTES-HEAT Almohadilla calentador KTES para instalaciones bajo -0°C (32°F) KTES-CAM-N KTES kit con cubierta de cámara a color con soporte (NTSC) KTES-CAM-P KTES kit con cubierta de cámara a color con soporte (PAL) KTES-INDEX-F KTES Directorio de papel indexado iluminado con LED KTES-INDEX-R KTES anillo recorte de papel indexado para ser utilizado con una instalación “flush” de KTES-INDEX-F KTES-POSTAL KTES soporte de cerradura con interruptor KTES-MPLATE KTES plato de montaje para instalación con cuello de ganso E-KTES Certificado para aumentar 1 KTES hasta ,000 inquilinos Optional Tenant code can’t be combined, it is not additional tenant, it is a total Validate list transfer when changing code (Speaker's Name)
13 Número de Parte – RepuestosTYCO '05 GLM 9/24/ :42 PM Número de Parte – Repuestos KT-TAMPER Interruptor anti-sabotaje para gabinete KTES-LOCK Cerradura para armario con 2 llaves KTES-SPEAK Ensamblaje para bocina KTES-LCD Ensamblaje para módulo LCD KTES-MPCA Ensamblaje principal para PCB KTES-DCPA Door PCB assembly with keypad and microphone KTES-LENS LCD clear lens (Speaker's Name)
14 Part Number – No Phone Bill (N.A. only)TYCO '05 GLM 9/24/ :42 PM Part Number – No Phone Bill (N.A. only) KTES-5048MC Main controller for up to 48 lines KTES-5000MC Main controller for up to 1152 lines Requires auxiliary relay cabinet (KTES-5000AC) KTES-5000AC Auxiliary relay cabinet for up to 96 lines (8 relay boards) To be use with KTES-5000MC main controller KTES-RB Relay board (12 tenants per board) KTES-IC Cable for relay board(12 tenants per board) Each Main controller require a KTES-RB12 relay board per 12 lines and a 16VAC 40VA transformer. (Speaker's Name)
15 Reader IN / Reader OUT Lock Relay 1 – 2 – 3 4 inputs 485 CommunicationTYCO '05 GLM 9/24/ :42 PM Reader IN / Reader OUT Lock Relay 1 – 2 – 3 4 inputs 485 Communication AC/DC power input AUX 12V output Tamper Phone line IP Communication JP9 = Reader Power; 5, 12 or ext. JP1-JP2 = Reset Type COM2 Not Used (Speaker's Name)
16 Hardware connection – Locking DeviceInternal power (12V, 650mA) OR External power (Using relay to follow lock output)
17 Hardware connection – InputsInput 1 = Door contact Input 2 = Postal lock Input 3 = REX Input 4 = Undefined None, single or double EOL
18 Hardware connection – Reader (Optional)TYCO '05 GLM 9/24/ :42 PM Hardware connection – Reader (Optional) Possible to have an external reader Set reader voltage with JP9 Possible to integrate with access controller requiring: LED connection Keypad programming of Full EntraPass Jumpers must be set to OUT Reader types:26bit, 34 bit, KSF and XSF Display format: HH:DDDDD, HHHH:DDDDD, DDDDDDDD(8 digits), DDDDDDDDDD(10 digits), HH:HHHH, HHHH:HHHH (Speaker's Name)
19 Hardware connection – Phone lineTYCO '05 GLM 9/24/ :42 PM Hardware connection – Phone line Connect phone line to TIP & Ring terminal Up to 5 units on the same line. Connected in parallel on TIP & RING (3 if using dial-up) Australia and New Zealand Connect ferrite TIP and RING are reversible (Speaker's Name)
20 Hardware connection – PowerTYCO '05 GLM 9/24/ :42 PM Hardware connection – Power Connect Earth ground Connect main power Connect the battery Note: The battery must be kept indoor if the outdoor temperature drops below -25°C (-13°F). Important: The KTES will not start on backup battery alone. (Speaker's Name)
21 Using the unit – Calling a tenantSelect language (if required) Press the center button until desired language is displayed Call Tenant: Type in Tenant ID on keypad Select tenant from list Select List (press left button) Use ↑ (left button) or ↓ (right button) to move cursor (>) to desired tenant Press Call (center button) Search tenant Select Find (press right button) Press the digit corresponding to the first letter of the desired tenant Use ↑ or ↓ to move cursor (>) to desired tenant (if required)
22 Using the unit – Granting or Denying accessTenant phone ring No answer within defined number of ring (5), unit display No Answer. If alternate phone number exist for tenant, unit dial it. No answer within number of ring, unit display No Answer. Tenant answer the phone Countdown timer for talk time appear on right A beep will be heard at the warning time System hang up at the end of the countdown Tenant press an action key on his phone 9 to grant access (customizable key). Unit display Access Allowed and unlock door. * to deny access (customizable key). Unit display Access Denied. Defined key for auxiliary relay. Unit display Alternate Access and activate relay. Calling Tenant name 00:40 Vol- Cancel Vol+
23 Using the unit – Tenant accessAccessing the building with a PIN Press the * key Enter Tenant PIN Unit display Access Granted and unlock door Accessing the building using a card (require a reader) Present Tenant card to reader
24 Programming the KTES – Accessing itAccess the VUI (Visual User Interface) Hold the * key for 5 seconds (the unit will beep after 5 seconds) Enter the default Installer PIN 8888 The star key * can also be used as the Exit or Escape key. The pound key # is the Enter key. Note: For security purposes, you should change your PIN to a different value as soon as possible.
25 Programming the KTES – Entering textBkSp Caps Next The system support capital as well as lower cases letters. The panel middle key allows you to choose your preference: • Caps: First letter after a space is capitalized (default). • CAPS: All capital letters • caps: All letters will be lower case.
26 Programming the KTES – Entering textEnter text as you will do when sending text message on mobile phone (Pressing 2 will show A, pressing it again will show B, etc.). See table below for characters list.
27 Programming the KTES – Stand aloneFor any installation not using AC - 60 Hz to power the unit, set Time Base to Xtal. ( ) For any installation outside North America, Set Tel interface ( ) code from the following list:
28 Programming the KTES – Stand aloneTYCO '05 GLM 9/24/ :42 PM Programming the KTES – Stand alone Set Daylight Saving time if required ( , ) Set time (3-1) and date (3-2) Set Welcome messages (2) Set Language ( ) M=Main, E=Enable, D=Disable Change Installer code and add tenant (1) Call a tenant and validate functionality and audio Adjust audio if necessary using Live adjustment ( ) Customize to specific need. Setting the time will disable all communication protocols. Live adjustment will get you out of the menu and show up on display on next tenant call. Mic volume is a threshold (Speaker's Name)
29 Status of the unit – LED StatusTYCO '05 GLM 9/24/ :42 PM Status of the unit – LED Status TXRX (YELLOW) LED is OFF when there is no Ethernet network/cable unplug FLASHING when there is network activity; and ON when the network is present 100 (GREEN) LED is ON only when the KTES is connected at 100 Mb/s. Network Link (100) ,Network Activity (TXRX) , AC Power, DC Power, Heartbeat, Lock, Relay 1-2-3 (Speaker's Name)
30 Status of the unit Look for message on display Check event logTamperSwitch PowerFail BatteryTrouble BufferFull70 Only when link with EntraPass Stand alone = FIFO (4096 events) OtherTrouble READER_POWER_FAILURE LOCK_POWER_FAILURE AUX_POWER_FAILURE PHONE_LINE_TROUBLE A=Alarm R=Restore ForcedOpen OpenToLong LeftOpen LockTrouble KeyPadLockout DuressAlarm *A only AccessGranted Access Denied = Invalid Access Schedule VisitorAllowed AltVisitorAllowed VisitorDenied UserTrace, InvalidStatus OtherAccessDenied = Denied by external controller
31 TYCO '05 GLM 9/24/ :42 PM Reset the unit Display Contrast, MIC and SPKR volume will never be reset (Speaker's Name)
32 Connection with EntraPassTYCO '05 GLM 9/24/ :42 PM Connection with EntraPass Dial up is 1 KTES per site. No Slave KTES or Controller IP is 1 KTES per Site. No Slave KTES or Controller. Fix IP only KTES can be slave on a controller loop over IP Link, KT-400-IP, 485 loop. No KTES behind dial up site. (Speaker's Name)
33 EntraPass KTES EditionFree with each KTES Same CD Different install code Possible to Upgrade to full Special Edition with EntrePass SE code. Possible to Migrate to EntraPass Corporate or Global
34 EntraPass KTES EditionNew Wizard New Icon under Device New Icon under Users
35 Connection with EntraPassConnection under Special or CE Gateway Latest EntraPass version required Wizard available on all version via Devices - KTES
36 Connection with EntraPass – Dial upTYCO '05 GLM 9/24/ :42 PM Connection with EntraPass – Dial up Do not use the box CODE TO ACCESS AN OUSIDE LINE Maximum speed is 2400 Only 1 unit per site Multiple unit (site) can be connected on the same phone line (up to 3) (Speaker's Name)
37 Connection with EntraPass – IPFix IP only (no DHCP and DNS) for KTES KTES Serial Number will be populated once IP connection is made SE or Gateway requires a fix IP If SE or Gateway IP change, it is possible to change it from the KTES ( ), no need to hard Reset Only 1 unit per site Multiple unit (site) can be connected on the same phone line (up to 5)
38 Connection with EntraPassDefine unit and site in EntraPass Establish connection with EntraPass From the unit, call a tenant and validate functionality and audio Adjust audio if necessary using Live adjustment ( ) Audio and contrast can only be adjusted from unit. Customize to specific need. Print tenant list from Device – KTES windows
39 Connection with access controller (Wiegand integration)Available in Stand Alone or FULL EntraPass only Not available on EntraPass KTES Edition KTES unit becomes a slave REX stop working Relay activation on access event stop working Unit send Wiegand string to controller Adjust messages on screen according to LED signal Signal must be set to GND for at least 1 second. We can short LED to GND on reader port 2 to have the unit always display Access Granted.
40 Thank You!